U.S. PHARMACOPEIA

Search USP29  
Verapamil Hydrochloride Tablets
» Verapamil Hydrochloride Tablets contain not less than 90.0 percent and not more than 110.0 percent of the labeled amount of verapamil hydrochloride (C27H38 N2O4·HCl).
Packaging and storage— Preserve in tight, light-resistant containers.
Identification—
Test specimen— Transfer a portion of finely powdered Tablets, equivalent to about 25 mg of verapamil hydrochloride, to a separator. Add 25 mL of water, and shake by mechanical means for 30 minutes. Add 1 mL of 1 N sodium hydroxide, and extract with 25 mL of chloroform, shaking by mechanical means for 10 minutes. Pass the chloroform extract through a filter containing anhydrous sodium sulfate. Triturate the chloroform extract with 400 mg of potassium bromide and evaporate to dryness. Dry at 105 for 2 hours.
B: The retention time of the major peak in the chromatogram of the Assay preparation corresponds to that in the chromatogram of the Standard preparation, as obtained in the Assay.
Dissolution 711
Medium: 0.01 N hydrochloric acid; 900 mL.
Apparatus 2: 50 rpm.
Time: 30 minutes.
Procedure— Determine the amount of C27H38N2O4·HCl dissolved from the difference between UV absorbances at the wavelengths of maximum absorbance at about 278 nm and 300 nm using filtered portions of the solution under test, suitably diluted with Medium if necessary, in comparison with a Standard solution having a known concentration of USP Verapamil Hydrochloride RS in the same Medium.
Tolerances— Not less than 75% (Q) of the labeled amount of C27H38N2O4·HCl is dissolved in 30 minutes.
Uniformity of dosage units 905: meet the requirements.
Procedure for content uniformity— Transfer 1 Tablet to a 100-mL volumetric flask, add 50 mL of 0.01 N hydrochloric acid, and heat on a steam bath for 50 minutes. Sonicate the heated solution for about 10 minutes, cool, dilute with 0.01 N hydrochloric acid to volume, mix, and filter. Dilute an accurately measured portion of the filtrate quantitatively with 0.01 N hydrochloric acid to obtain a Test preparation containing about 48 µg of verapamil hydrochloride per mL. Dissolve an accurately weighed quantity of USP Verapamil Hydrochloride RS in 0.01 N hydrochloric acid to obtain a Standard preparation having a known concentration of about 48 µg per mL. Concomitantly determine the absorbances of the Test preparation and the Standard preparation in 1-cm cells at the wavelength of maximum absorbance at about 278 nm and the absorbance of the Test preparation at 300 nm, with a suitable spectrophotometer using 0.01 N hydrochloric acid as the blank. Calculate the quantity, in mg, of C27H38N2O4·HCl in the Tablet taken by the formula:
(TC / D)(AU / AS),
in which T is the labeled quantity, in mg, of verapamil hydrochloride in the Tablet; C is the concentration, in µg per mL, of USP Verapamil Hydrochloride RS in the Standard preparation; D is the concentration, in µg per mL, of verapamil hydrochloride in the Test preparation, on the basis of the labeled quantity per Tablet and the extent of dilution; AU is the difference between absorbances at 278 nm and 300 nm of the Test preparation; and AS is the absorbance of the Standard preparation at 278 nm.
Related compounds—
Aqueous solvent mixture , Mobile phase, System suitability solution, and Chromatographic system—Proceed as directed in the test for Chromatographic purity under Verapamil Hydrochloride.
Standard solution— Dissolve accurately weighed quantities of USP Verapamil Hydrochloride RS, USP Verapamil Related Compound A RS, 3,4-dimethoxybenzaldehyde, and 3,4-dimethoxybenzyl alcohol in Mobile phase to obtain a solution having known concentrations of about 1.6 mg of USP Verapamil Hydrochloride RS per mL and 0.0048 mg each of USP Verapamil Related Compound A RS, 3,4-dimethoxybenzaldehyde, and 3,4-dimethoxybenzyl alcohol per mL.
Test solution— Use the Assay preparation.
Procedure— Separately inject equal volumes (about 10 µL) of the Standard solution and the Test solution into the chromatograph, and allow the Test solution to elute for not less than four times the retention time for verapamil. Record the chromatograms, and measure all of the peak responses. [NOTE—The retention times are about 0.4 for 3,4-dimethoxybenzyl alcohol, 0.5 for verapamil related compound A, 0.7 for 3,4-dimethoxybenzaldehyde, and 1.0 for verapamil.] Calculate the quantity, in mg, of each individual impurity in each mL of the portion of Tablets taken by the formula:
25C(rU / rS),
in which C is the concentration, in mg per mL, of the appropriate impurity in the Standard solution; and rU and rS are the peak responses of the appropriate impurity obtained from the Test solution and the Standard solution, respectively: not more than 0.3% of any specified impurity is found; and the sum of all impurities is not more than 1.0%.
Residual solvents 467: meet the requirements.
(Official January 1, 2007)
Assay—
Aqueous solvent mixture , Mobile phase, System suitability solution, and Chromatographic system—Proceed as directed in the test for Chromatographic purity under Verapamil Hydrochloride.
Standard preparation— Dissolve an accurately weighed quantity of USP Verapamil Hydrochloride RS in Mobile phase to obtain a solution having a known concentration of about 1.6 mg per mL.
Assay preparation— Weigh and finely powder not fewer than 20 Tablets. Transfer an accurately weighed portion of the powder, equivalent to about 40 mg of verapamil hydrochloride, to a stoppered centrifuge tube, and add 25 mL of Mobile phase. Shake by mechanical means for 15 minutes, centrifuge, and if necessary filter the supernatant.
Procedure— Separately inject equal volumes (about 10 µL) of the Standard preparation and the Assay preparation into the chromatograph, and allow the Assay preparation to elute for not less than four times the retention time for verapamil. Record the chromatograms, and measure the responses for all of the major peaks. Calculate the quantity, in mg, of verapamil hydrochloride (C27H38N2O4·HCl) in the portion of Tablets taken by the formula:
25C(rU / rS),
in which C is the concentration, in mg per mL, of USP Verapamil Hydrochloride RS in the Standard preparation; and rU and rS are the peak responses obtained from the Assay preparation and the Standard preparation, respectively.
Auxiliary Information— Staff Liaison : Andrzej Wilk, Ph.D., Senior Scientific Associate
Expert Committee : (MDCV05) Monograph Development-Cardiovascular
USP29–NF24 Page 2246
Phone Number : 1-301-816-8305