Medium: 0.0005% (w/v) polysorbate 80; 500 mL.

Apparatus 2: 75 rpm.

Time: 60 minutes.

Mobile phase— Prepare a filtered and degassed mixture of water and acetonitrile (3:2). Make adjustments if necessary (see System Suitability under Chromatography 621).

Standard solution [Note—A volume of alcohol not exceeding 2% of the final volume of the solution may be used to aid in dissolving the USP Reference Standards.]—Dissolve an accurately weighed quantity of USP Norgestrel RS and USP Ethinyl Estradiol RS in Medium, and dilute quantitatively, and stepwise if necessary, with Medium to obtain a solution having known concentrations similar to those expected in the Test solution.

Test solution— Use a portion of the solution under test filtered through 0.7-µm borosilicate microfiber filter.

Chromatographic system (see Chromatography 621)— The liquid chromatograph is equipped with a 247-nm detector (for norgestrel analysis), and a spectrofluorometric detector (for ethinyl estradiol analysis) with an excitation wavelength of about 285 nm and an emission wavelength of 310 nm, and a 4.6-mm × 15-cm column that contains packing L7. The flow rate is about 1 mL per minute. Chromatograph the Standard solution, and record the peak responses as directed for Procedure: the relative retention times are about 0.7 for ethinyl estradiol and 1.0 for norgestrel; and the relative standard deviation for replicate injections is not more than 3.0% for the ethinyl estradiol and norgestrel peaks.

Procedure— Separately inject equal volumes (about 100 µL) of the Standard solution and the Test solution into the chromatograph, record the chromatograms, and measure the responses for the major peaks. Calculate the quantities, in mg, of norgestrel (C21H28O2) and ethinyl estradiol (C20H24O2) dissolved by the formula: in which C is the concentration, in mg per mL, of the appropriate USP Reference Standard in the Standard solution; and rU and rS are the peak responses obtained from the Test solution and the Standard solution, respectively.

Tolerances— Not less than 75% (Q) of the labeled amount of C21H28O2 and C20H24O2 is dissolved in 60 minutes.

(Official January 1, 2007)

Mobile phase— Prepare a degassed mixture of water, acetonitrile, and methanol (45:35:15). Make adjustments if necessary (see System Suitability under Chromatography 621).

Standard preparation— Dissolve an accurately weighed quantity of USP Norgestrel RS and USP Ethinyl Estradiol RS in Mobile phase, and dilute quantitatively, and stepwise if necessary, with Mobile phase to obtain a solution having known concentrations of about 100 µg of norgestrel per mL and 10 µg of ethinyl estradiol per mL.

Assay preparation— Transfer an accurately counted number of Tablets, equivalent to about 10 mg of norgestrel, to a 200-mL volumetric flask. Add 100.0 mL of Mobile phase, accurately measured, sonicate for 10 minutes to disintegrate the Tablets, and shake by mechanical means for 20 minutes. Centrifuge the clear portion of the solution at about 2000 rpm for 10 minutes, and filter the clear supernatant.

Chromatographic system (see Chromatography 621)— The liquid chromatograph is equipped with a 215-nm detector and a 4.6-mm × 15-cm column that contains 5-µm packing L7. The flow rate is about 1 mL per minute. Chromatograph the Standard preparation, and record the peak responses as directed for Procedure: the relative retention times are about 1.0 for ethinyl estradiol and 1.5 for norgestrel; the resolution, R, between the two major peaks is not less than 2.5; and the relative standard deviation for replicate injections is not more than 2.0%.

Procedure— Separately inject equal volumes (about 50 µL) of the Standard preparation and the Assay preparation into the chromatograph, record the chromatograms, and measure the responses for the major peaks. Calculate the quantity, in mg, of ethinyl estradiol (C20H24O2) and norgestrel (C21H28O2) in the portion of Tablets taken by the formula: in which C is the concentration, in mg per mL, of the relevant USP Reference Standard in the Standard preparation; and rU and rS are the peak responses for the relevant analyte obtained from the Assay preparation and the Standard preparation, respectively.