Medium: water; 500 mL.

Apparatus 2: 50 rpm, the distance between the paddle blade and the inside bottom of the vessel being maintained at 4.5 ± 0.2 cm during the test.

Time: 30 minutes.

Mobile phase— Prepare as directed in the Assay.

Standard solution— Dissolve an accurately weighed quantity of USP Ergoloid Mesylates RS in water to obtain a solution having a known concentration of about 50 µg per mL. Transfer 4 mL of this solution for every 0.5 mg of ergoloid mesylates contained in the Tablets to a 200-mL volumetric flask, add 1 mL of 0.1 N hydrochloric acid and 100 mL of water, mix, and dilute with water to volume.

Test solution— Transfer a 20-mL portion of the solution under test to a suitable container, add 100 µL of 0.1 N hydrochloric acid, and mix.

Chromatographic system— Proceed as directed in the Assay except that the sum of the relative standard deviation values for the four ergoloid mesylates peaks for replicate injections is not more than 3.0%.

Procedure— Separately inject equal volumes (about 500 µL) of the Standard solution and the Test solution into the chromatograph, record the chromatograms, and measure the responses for the major peaks. Calculate the quantity of ergoloid mesylates as directed in the Assay.

Tolerances— Not less than 75% (Q) of the labeled amount of ergoloid mesylates is dissolved in 30 minutes.

(Official January 1, 2007)

Mobile phase— Prepare a filtered and degassed solution containing a mixture of water, acetonitrile, and triethylamine (700:300:9). Make adjustments if necessary (see System Suitability under Chromatography 621).

Internal standard solution— Transfer about 113 mg of papaverine hydrochloride to a 1-L flask. Add a mixture of 0.01 M tartaric acid and acetonitrile (2:1) to volume, and mix.

Standard preparation— Transfer about 33 mg of USP Ergoloid Mesylates RS, accurately weighed, to a 100-mL volumetric flask. Dissolve in and dilute with Internal standard solution to volume, and mix. Use a freshly prepared solution.

Assay preparation— Weigh and finely powder not fewer than 20 Tablets. Transfer an accurately weighed portion of the powder, equivalent to about 5 mg of ergoloid mesylates, to a 50-mL centrifuge tube. Add 15.0 mL of Internal standard solution, insert the stopper into the tube, and shake for about 15 minutes. Centrifuge, filter if necessary, and use the clear supernatant.

Chromatographic system (see Chromatography 621)— The liquid chromatograph is equipped with a 280-nm detector and a 4.6-mm × 15-cm column that contains packing L1. [NOTE—Use an L1 column capable of handling pH values greater than 11.] The flow rate is about 1.5 mL per minute. Chromatograph the Standard preparation, and record the peak responses as directed for Procedure: the column efficiency determined for the dihydro--ergocryptine mesylate peak is not less than 1000 theoretical plates; the tailing factor for the dihydro--ergocryptine mesylate peak is not more than 2.0; the resolution, R, between the dihydro--ergocryptine mesylate and dihydroergocristine mesylate is not less than 2.0, and between dihydroergocristine and dihydro--ergocryptine peaks is not less than 2.0; and the relative standard deviation of the ratio of the sum of the four peaks to the internal standard for replicate injections is not more than 1.5%.

Procedure— Separately inject equal volumes (about 20 µL) of the Standard preparation and the Assay preparation into the chromatograph, record the chromatograms, and measure the responses for the major peaks. The order of elution is papaverine, dihydroergocornine, dihydro--ergocryptine, dihydroergocristine, and dihydro--ergocryptine. Calculate the quantity, in mg, of ergoloid mesylates in the portion of Tablets taken by the formula: in which C is the concentration, in mg per mL, of USP Ergoloid Mesylates RS in the Standard preparation; and RU and RS are the sums of the ratios of responses of the four major peaks to the response of the internal standard peak obtained from the Assay preparation and the Standard preparation, respectively. Calculate the percentage of each of the individual alkaloids taken by the formula: in which Ri is the peak response ratio of the individual alkaloid to the internal standard; (MW)i is the molecular weight of the individual alkaloid; and S[Ri(MW)i] is the summation of the products of peak response ratios and molecular weights for the four alkaloids.