Medium: 0.1 N hydrochloric acid; 900 mL.

Apparatus 2: 50 rpm.

Time: 30 minutes.

Procedure— Determine the amount of C24H40N8O4 dissolved by employing UV absorption at the wavelength of maximum absorbance at about 282 nm on filtered portions of the solution under test, suitably diluted with Medium, if necessary, in comparison with a Standard solution having a known concentration of USP Dipyridamole RS in the same Medium.

Tolerances— Not less than 70% (Q) of the labeled amount of C24H40N8O4 is dissolved in 30 minutes.

Procedure for content uniformity— Transfer 1 Tablet to a 100-mL volumetric flask, add 50 mL of 1 N hydrochloric acid, heat in a steam bath for 5 minutes, and shake by mechanical means for 30 minutes. Cool to room temperature, dilute with 1 N hydrochloric acid to volume, and mix. Filter, discarding the first 25 mL of the filtrate. Dilute an accurately measured portion of the subsequent filtrate with 1 N hydrochloric acid to provide a solution containing about 10 µg of dipyridamole per mL. Concomitantly determine the absorbances of this solution and of a solution of USP Dipyridamole RS in the same medium having a known concentration of about 10 µg per mL, in 1-cm cells at the wavelength of maximum absorbance at about 282 nm using 1 N hydrochloric acid as the blank. Calculate the quantity, in mg, of C24H40N8O4 in the Tablet taken by the formula: in which T is the labeled quantity, in mg, of dipyridamole in the Tablet; C is the concentration, in µg per mL, of USP Dipyridamole RS in the Standard solution; D is the concentration, in µg per mL, of dipyridamole in the solution from the Tablet based upon the labeled quantity per Tablet and the extent of dilution; and AU and AS are the absorbances of the solution from the Tablet and the Standard solution, respectively.

(Official January 1, 2007)

Mobile phase— Dissolve 250 mg of dibasic sodium phosphate in 250 mL of water, and adjust with dilute phosphoric acid (1 in 3) to a pH of 4.6. Add 750 mL of methanol, mix, filter through a 0.5-µm membrane filter, and degas. Make adjustments if necessary (see System Suitability under Chromatography 621).

Standard preparation— Using an accurately weighed quantity of USP Dipyridamole RS, prepare a solution in Mobile phase having a known concentration of about 15 µg per mL.

Assay preparation— Transfer not less than 20 Tablets to a 1000-mL volumetric flask, add 100 mL of water, and sonicate for 15 minutes. Add about 750 mL of methanol, and shake by mechanical means for 30 minutes. Dilute with methanol to volume, mix, and centrifuge. Dilute an accurately measured volume (VS mL) of the clear supernatant quantitatively with Mobile phase to obtain a solution (VA mL) containing about 15 µg of dipyridamole per mL.

Chromatographic system (see Chromatography 621)— The liquid chromatograph is equipped with a 288-nm detector and a 3.9-mm × 30-cm column that contains packing L1. The flow rate is about 1.5 mL per minute. Chromatograph the Standard preparation, and record the peak responses as directed for Procedure: the column efficiency determined from the analyte peak is not less than 1000 theoretical plates, the tailing factor for the analyte peak is not more than 2.0, and the relative standard deviation for replicate injections is not more than 2.0%.

Procedure— Separately inject equal volumes (about 50 µL) of the Standard preparation and the Assay preparation into the chromatograph, record the chromatograms, and measure the responses for the major peaks. Calculate the quantity, in mg, of C24H40N8O4 in the Tablets taken by the formula: in which C is the concentration, in µg per mL, of USP Dipyridamole RS in the Standard preparation; VA is the volume, in mL, of the Assay preparation; VS is the volume, in mL, of supernatant taken for the Assay preparation; and rU and rS are the peak responses obtained from the Assay preparation and the Standard preparation, respectively.